Can i convert this
ActiveCell. Offset(-1, 0).Copy
With ActiveCell
.PasteSpecial Paste:=xlPasteFormats, Operation:=xlNone, _
SkipBlanks:=False, Transpose:=False
.ClearOutline
End With
So that i can copy/paste the Offset range such as (-1,-2) (-1,1)?
I created macro that copies cells from one worksheet to another using the copy/paste function. Unfortunately it runs rather slow. Instead of copy and paste I want to use something like this:
ActiveCell.Offset(0,1)= Sheets("Raw Data").ActiveCell.Offset(2, 3)
Can this be done and what is the proper syntax?
Does this code copy all cells from the active cell up to the last non-blank cell, or is it up to the first blank cell after the last non-blank cell?
View 9 Replies View RelatedI have a combobox which is linked to a list of policies which has information to the right of them, upon changing the value in the combobox the subroutine below is activated.
It stores the value of the combobox in a string variable, goes to the list and searches for the cell containing the policy. Upon finding the cell it uses the range offset operation to select the two boxes to the right of the active cell. This is where I get my error 1004 - application or object defined error.
Code
Private Sub cmbSectionName_Change()
Dim mySearch As String
'Assigns combobox contents to mysearch
mySearch = cmbSectionName.Value
'select the range
Application.Goto Reference:="SectionNameList"
trying to make a copy range of cells from an activecell.
My activecell is P9 and I want to copy the contents of P1 to P18 without losing P9 as the activecell.
I want to use the following command but with more to it:
X=0
Y=0
Z=10
ActiveCell.Offset(rowOffset:=X, columnOffset:=Y).Activate
I want to use this type of command to highlight an area...not just move rows/columns. I want it to highlight from a point on the sheet marked by X and Y and then down Z rows.
So if I'm in cell A1 and want to highight from A1 down to A10, I'm not sure how to write that part of the code.
when the user enters the letter Y in a cell within a set column a macro kicks in and enters a VLOOKUP formula in a cell 1 row above and 4 columns to the left by using ActiveCell.Offset (-1,-4).
This seems to work fine however when I try and get the coding to copy and paste special as values it just seems to ignore it?
I'm trying to copy a range, specified by an offset, then PasteSpecial that range to yet another location specified by an offset.
This is the code I have so far, which does not attempt to find the range to copy via an offset.
I would appreciate some ones help to correct a macro I'm trying to write. The macro copies 3 columns from Sheet1 to Sheet2 in a selected location. The 3rd column copied needs to be pasted in a different column in Sheet2.
View 6 Replies View RelatedSub TestSearch()
Dim FoundCell As Range
Dim SearchString As Variant
'Specify Value to Search
SearchString = " Excel"
'Perform the Search and Return a Cell Value
Set FoundCell = Worksheets("Source").Range("A1:A10000").Find(" Excel", lookat:=xlPart)
If Not FoundCell Is Nothing Then
MsgBox "Found at " & FoundCell.Address
End If
End Sub
I'd like to take the code above, which returns a cell address which contains the text " Excel" and modify or add to it the capability to copy a range starting from the address returned and ending 102 cells further down in Column A on the Source sheet to A1 of the Sheet1 sheet. The crux of the problem seems to be converting the address to a row number then adding the value of the number of cells in the range to find the end row number then converting that back to an address??
What can I add to the macro I already have in place (below) to accomplish what I'm looking for (2 parts)? ...
1) I need to copy everything (formulas) that is in C7:F7 and paste it down to all "active" rows - I'm defining an active row by any row where column A is not blank.
2) I need to copy everything (formulas) that is in Q7:AF7 and paste it down to all "active" rows - I'm defining an active row by any row where column P is not blank. (You'll notice by the screenshot that there will be blank cells in column P mixed in with non-blank cells.)
Code:
Sub AdminTool()
'
' CreateAdminTool Macro
'
'
ActiveWindow.Zoom = 90
Rows("1:1").Select
Selection.Insert Shift:=xlDown, CopyOrigin:=xlFormatFromLeftOrAbove
[Code] ...........
I have a custom email creation template I am merging with another version. The problem I am having is wrapping my head around not only selecting a range that is offset from ActiveCell (column 6-9) but seeing if there is an "x" in that range which is normally blank. My previous attempts identify the "x" but adds the text every time it is found. (Each column is a flag for an email bullet and they can have all four bullets in the email where I only want the text included ONCE if they have ANY bullets included). I use the range because I do not want the text included if none of the bullets are used.
Teh StandHTML then gets used in the body of the email like other HTML items I use
The email is generated using the ActiveCell.Offset to insert special text, emails and routing and has weathered alot of changes over time.
Dim Myrange As Range
Myrange = Range(ActiveCell.Offset(0, 6), ActiveCell.Offset(0, 9)).Select
If Myrange = "x" Then
StandHTML = StandHTML & "Important Text"
End If
I am trying to copy the active cell from a range on sheet 1 to a new sheet ( Sheet 2 )in the next available row of Column B ONLY if the value changes from being blank.
If it was not empty I dont want it to be copied.
I cant seem to get my onChange event to copy anything.
I want my code to verify that the Active Cell on a worksheet falls within a specified range of cells before the sub fires off.
View 9 Replies View RelatedI would like to select multiple active cells (in different columns) and have them copied and pasted in another sheet. The current macro I am using seem to work fine, except for the fact that it only selects cell A3 to the end of the list in that active column. I would like it to also select B3 - down, C3 - down, and E3 - down.
I "Bolded" where I think the problem lies.
Sub Sort()
Sheets("Univerity Rankings").Select
Range("a3:z10000").Select
[Code].....
with some basic code. I want to check the activecell, if it's blank then copy the contents from the cell above, if it's not blank, leave it & go down to the next cell & repeat until last row.
View 7 Replies View RelatedI've been trying to get the sum of a range of cells based on their relation to the active cell. Here is the Pseudo
If the SUM of (the cell 2 rows up THROUGH the cell 2 rows up and 2 columns to the left) = 0 then .......
*****end pseudo
I think that activecell.offset is the best way to do it, but I can't figure out how to work that in a range....
Here is my code so far:
Worksheets("Generic SPC").Activate
Worksheets("Generic SPC").Range("c2").Select
'Do for all cells in the row
Do
ActiveCell.Offset(0, 1).Select
If Application.WorksheetFunction.Sum(Range( _
ActiveCell.Offset(-2, 0), ActiveCell.Offset(-2, 2))) = 0 Then
ActiveCell.Value = 0
ElseIf Application.WorksheetFunction.Sum(Range _
("ActiveCell.Offset(-2, 1), ActiveCell.Offset(-2, 3)")) = 0 Then
ActiveCell.Value = ActiveCell.Offset(-2, 0).Value
Else: ActiveCell.Value = 0
End If
Loop Until IsEmpty(ActiveCell.Offset(0, 1)) = True
******End Code
Range doesn't like activecell.offset. Does anyone know how to do this?
Following Dave's rule regarding using the rows in Excel rather than the columns I am trying to re organise some workbooks that have been passed to me. To copy one column of information requires 4 pages of code the first section of which is below.
Sub Copy1()
Sheets("INPUT_SHEET2").Select
Range("F4").Select
Selection.Copy
Sheets("INPUT1").Select
Range("C6").Select
Selection.PasteSpecial Paste:=xlValues, Operation:=xlNone, SkipBlanks:= _
False, Transpose:=False
End Sub
Now that I have the code to copy one column I want to be able to adapt it to move four columns to the right from F to J and using the example above copy from J4 to C166. I am guessing that Offset is the way to do this but can't seem to work out how. ach block of data takes up 160 rows and the data is all pasted into column C. The data to be pasted starts in row F then J then N and so on up to column IZ in some of the workbooks I am trying to revamp.
Copying the target cell to target.offset(0,-3)
View 5 Replies View RelatedI am trying to locate specific values in column a of a spreadsheet and I want to be able to move (cut and paste, offset, ???) only those values to column c of the same row. The values I am looking for are text and they all begin <@29>, <@33>, etc. (pagemaker codes). I want to move the cells with the pagemaker codes to column c. and leave the other ones in column a. Does anybody know how to do this using vba? Below is a sample of my column a.
16D
16D
16D
16D
16D
16D
16D
16D
16D
16D.........
I need to create a macro wheather it be for each row or perhaps a dynamic macro that based on the active cell it can then offset based on my Expense type(Column B) into the respective row.
i had placed a sample of what i need to come up with highlighted in red. I need to copy the data in C7, C8, C9, etc... into D7:N7, D8:N8, etc... I have over 950 rows this code will need to be copied to. Columns do not move.
So if choose "fixed then i need for the macro to copy and paste data in each of those cells for Febuary to December. Should i choose "variable" then it places a "0" for Febuary to December and should I choose "NA" then nothing happens and i dont need code for that. It needs to be running constantly that way i dont need to run the macro so it needs to be in a module i beleive.
My problem is that i have three years of data and i have over 950 rows for expenses. THis is just a morsol. I cant place code in the cells as the expenses go there and it will just over write the code and is useless to me. That is why i need a macro that based on what i choose it then copies January's expense appropriately and for now it doesnt need to be dynamic but i prefer that it be based on the active cell if this is possible as i used over 950 option buttons and it worked but as the file gets bigger it crashes my computer.. 'Not enough Resources" .. gigs of ram and a 3.6 processor..
This is the current code I am using, it works but from another post it looks like it could be cleaned up.
With Sheets("Web Data")
.Activate
Range(.Range("A6")).Offset(2, 1).Resize(2, 24).Copy
Sheets("MW Forecast Calculation").Select
Range("C9").Select
Selection.PasteSpecial Paste:=xlPasteValues, Operation:=xlNone, SkipBlanks _
:=False, Transpose:=False
This is the code I am trying to get to work but I am having trouble with the red text.
Set CopyRange = Sheets("Web Data") Range(.Range("A6")).Offset(2, 1).Resize(2, 24).Copy
Set PasteRange = Sheets("MW Forecast Calculation")
Cells ("C9:Z10")
CopyRange.Copy PasteRange.Values
My source data generates a sheet full of individual dates and condo rates. We'll call it the "Rates Tab". The dates are not sorted or organized into a single column and to complicate it further the data has blank rows periodically. The only recognizable pattern is: (example) the date is in cell b12, then the condo rate will be 2 columns to the right in d12. On a separate sheet, the user will input a check in date(date A) and check out date(date b). I need to find the rates for all dates from Date A to Date B located on the Rates Tab. how to find a Date across various columns and then return a value 2 columns to the right from the "target"?
View 6 Replies View RelatedAs seen in the attached spreadsheet on sheet1 the template is 6 columns and 5 rows. The colors correspond to the information needed on sheet 2. this template includes data from row 3 on sheet 2. I need a macro that will copy this template and return the next row of data from sheet2. this has me stumped. Also the data changes on sheet, so it may have many rows or just a couple.
View 7 Replies View RelatedI am having trouble with one line of this code that I can't figure out how to write correctly. I have set the range, but I need to offset by 10 rows up. My code fails at set rng.
View 6 Replies View RelatedI have an offset range ("TheCell") that does not seem be working how I would expect.
I don't know if its because the sheet I am working on was originaly German but I would be surprised if that was the case.
I Use sheet change to set the peramiters of the range and to test the value
Private Sub Worksheet_SelectionChange(ByVal Target As Range)
Dim rowcell
Dim colcell
Dim typeit
colcell = ActiveCell.Column
rowcell = ActiveCell.Row
ActiveWorkbook.Names.Add Name:="iname", RefersToR1C1:="=" & "Tabelle2!R1C" & colcell
ActiveWorkbook.Names.Add Name:="Jname", RefersToR1C1:="=" & "Tabelle2!R" & rowcell & "C2"
typeit = Range("TheCell").Value
MsgBox typeit
End Sub
=OFFSET(Tabelle1!$B$4,MATCH(Jname,Tabelle1!$B$5:$B$57,0),MATCH(iname,Tabelle1!$B$4:$EX$4,0)-1)
but for some reason I am getting a runtime error 1004 worksheet failed.
I have used this technique before and its been fine so what mistake have I made :o)
I want to apply some logic to a range. However I want to offset the bottom of the range by 1 row.
Example: I have a range (B8:I19) already defined in my vba code. But I want to shade range (B8:I20).
MyRange = Range("B8:B19")
MyRange.Offset(1, 0).Interior.ColorIndex=3
This code also offsets the top of the range (row 9), which I don't want.
How can I only offest the bottom of the range?
I am attempting to do is have a macro (Via Command button) go through column A to find the word "TOTAL". Once that is found I want it to offset by 3 rows (from the word "TOTAL") to grab the number and place it into column B.
View 2 Replies View RelatedI am trying to achieve something like this :
Find a specific text in my column B (example : "Proposal ID"), when "Proposal ID" is found, select this cell and offset to the column C (Offset(0, 1)). Then copy this cell value in another sheet.
This will be repeated with different texts (always in the column B), so if the text is not found, I need the macro to continue running.
using VBA and most of what i know has come from reading through blogs. I'm trying to copy 5 separate pieces of data from one row on our Payroll sheet and paste this in to another sheet call master dump.
The issue that i am having is that the code i have written keeps coming up with a run time error 1004 at the line "a.Select"
What i need the code to do is this: Copy the data from cell A4 and paste this on to another worksheet in to row cell b2, date worked in to d2, pay code in ot f2, hours in to h2 and the cost centre in to ad. all on the same row. i then need it to move on to the next team member (in this case A5) and repeat until there is no emp#. once the monday is done it will need to move onto Tuesday.
Code below.
Sub payroll_data()
'
' Payroll_data_MON Macro
Dim a As Range, b As Range, c As Range, d As Range, e As Range, i As Range, j As Range, k As Range, l As Range, m As Range
Set a = Range("A4")
Set b = Range("I4")
Set c = Range("G4")
Set d = Range("H4")
[code]....